A Practical Window-Cleaning Workflow for Basic Shopfront Glass
025 | Saturday, 26 September 2026, 7:36 AM
Cleaning a shopfront well is not just about knowing how to use a squeegee. A good window cleaning workflow is about doing each task in the right order, so you avoid creating extra work as you go.
For a basic shopfront, I work from the whole facade down to the individual panes: assessing the job, preparing the area, working from the top down, controlling the water, inspecting the result, then moving inside. This guide covers basic, accessible shopfront glass cleaned from ground level using traditional tools.
Assess the whole shopfront first
When I arrive, I position my trolley where it will not obstruct pedestrians, then stand back and inspect the whole shopfront. I am looking for things like:
cobwebs;
removable third-party stickers;
furniture blocking access;
dirty frames;
problem spots on the glass;
customers moving through the area;
sun, rain or glare;
awkward sections; and
pedestrian traffic.
From that, I decide the order in which I will work. Shopfront window cleaning is about more than making individual panes clean. The whole facade should look finished when you leave.
Prepare the facade before the glass
If there are cobwebs, I remove those first. If furniture is blocking access, I move it.
I also check the frames. If they are particularly dirty, I prefer to wash them before cleaning the glass. Otherwise, you can end up with clean windows surrounded by dirty frames.
For badly soiled frames, I use a wet applicator and then remove the water with a small squeegee.
Deal with anything likely to spoil the finished glass before you start washing the glass.
Work from the top down
If the shopfront has an upper and lower row of windows, I always start with the upper row. Water from the upper panes and frames will naturally move downward. If you clean the lower glass first, you may wet it again while working above it.
Top glass first → bottom glass second.
For smaller panes, I tend to use a squeegee channel that's around 40–50% of the height of the pane. That is my preference because it gives the squeegee room to move while still giving me good control.
Clean nearby panes in groups
Every pane of glass involves several tool changes. I use the applicator to wet the glass, switch to the squeegee to clean the pane, switch to a small squeegee to remove water from the trim, then switch to a cloth to detail the edges and remove any remaining marks.
If I group three panes together, I can wet all three, squeegee all three, clear the frame water and then detail them. The work is the same, but the sequence is more efficient.
Remove ledge water before detailing
This is a small part of the workflow that makes a big difference. After cleaning upper panes, water will accumulate on the lower frame or ledge beneath them. Before detailing the edges of the glass, I remove that water first. If you put a dry detailing cloth onto a wet frame, the cloth absorbs that water. You then transfer the moisture straight back onto the clean glass. Remove the bulk water first. Detail second.

I also wipe the front-facing section of the frame where water has spilled. If that water dries there, it can leave streaks that detract from the finished shopfront.
Move to the lower panes
Once the upper section is finished, I move onto the lower glass.
If there are removable third-party stickers, this is where I deal with them.
Detailed scraper technique is a separate skill and sits outside this basic workflow.
Then I wash the glass using an applicator.
One mistake I often see beginners make is moving the applicator around in large circles and arcs, scrubbing much harder than necessary. Unless the glass is particularly dirty or it is a first clean, you normally do not need that much movement.
My usual approach is controlled up-and-down strokes across the pane.
Permanent stickers and logos also need attention. Small droplets can remain around their edges even after the surrounding glass has been squeegeed. I use a dry cloth to collect that moisture before it has a chance to run down the clean glass.
Wet with the applicator → squeegee → remove ledge water → detail.
Inspect before moving inside
Once the exterior is finished, I stop and check it.
Large panes can hide streaks and missed areas depending on the viewing angle. I look at the glass from different positions and deliberately scan each pane from top to bottom.
Also mop up any water on the ground. It keeps the work area tidy and avoids leaving a slip hazard behind.
Plan the inside separately
The basic cleaning principles are similar inside, but the environment often changes.
You may have:
furniture;
shelving;
posters;
fixed displays; and
much tighter working spaces.
That means you need to stop and plan again instead of automatically repeating what you did outside.
Sometimes it is better not to wet the glass
A common problem is a fixed fixture sitting very close to the window.
If there is not enough room to hold the squeegee at the right angle and maintain proper contact with the glass, wetting that section can make the result worse.
Water may run in-between the fixture and the window where you cannot reach it.
For some small inaccessible areas, I use a very slightly damp cloth folded over the squeegee channel to loosen the soil, then replace it with a dry cloth to remove the remaining moisture. If there is a limitation like this, tell the customer what you found and what you did.
Be careful around posters
Shopfronts often have posters attached to the inside of the glass. Where practical, I prefer these to be removed rather than cleaning around them. Water can damage them, the squeegee can tear them, moisture can get behind them, and dirt can remain hidden underneath. If I am concerned about damaging something, I ask the customer to remove it.
Finish with a checklist
Once the inside and outside are complete, mop up any remaining water, return furniture to its original position and inspect the whole job again.
A simple completion checklist might include:

A good window cleaning workflow prevents rework
Good shopfront window cleaning is not just a collection of techniques. It is a sequence.
You assess before starting. Prepare before cleaning. Work from the top down. Control water before detailing. Inspect before moving on. Then check the whole job before calling it finished.
Those final few minutes of inspection give you confidence in the result and help build trust with the customer.
Want to practise this workflow with guidance? SqueegeeSchool’s half-day workshop gives you hands-on practice with professional tools, real shopfront glass and direct feedback on your technique.


Comments